SpanSizer
Structural Ready-Mix & Turnkey Pour CostsUpdated for 2026Commercial Grade

Concrete Cost Calculator (Delivered Ready-Mix Yards & Turnkey Labor)

Calculate total concrete pour costs including ready-mix yardage, short-load fees, rebar reinforcement, vapor barriers, and contractor labor per square foot.

Regional Market Calibration:Adjusts trade labor, concrete mix, and building codes to local city averages.
Popular Dimension Presets:
Engineered Slab Cutaway Cross-Section (ACI 302)Slab Thickness: 4" Commercial Grade
Broom Finished Concrete Surface4,000 PSI Poured Concrete (4" Slab)#4 Rebar (18" o.c.)10-Mil Heavy Duty Vapor Barrier Membrane (ASTM E1745)4" to 6" Compacted #57 Crushed Stone Base (95% Modified Proctor)

Cross-section demonstrates structural reinforcement elevation on concrete chairs per ACI 302.

Project Dimensions & Material Inputs

(feet)
feet
(feet)
feet
(inches)
inches

Total Ready-Mix Concrete Order

8.00 Cubic Yards (600 sq ft @ 4")

Delivered Ready-Mix Batch Volume

216 cu ft (32,400 lbs @ 4,000 PSI)

Contractor Bill of Materials (BOM) Breakdown

Item / Material SpecQuantityUnit / PackageInstallation Notes
4,000 PSI Ready-Mix Air-Entrained Concrete8.00Cubic YardsBatch plant delivery with 8% subgrade variance (ACI 302.1R)
#4 (1/2") Grade 60 Deformed Rebar Sticks3320-Ft Sticks18" on-center grid suspended 2" off subbase on dobies
10-Mil Polyethylene Vapor Retarder11,000 Sq Ft RollsASTM E1745 Class A underslab vapor barrier
2×4 Spruce-Pine-Fir Formwork Lumber912-Ft BoardsPerimeter forms with 2×4 bracing stakes every 3 feet

Estimated Project Cost Range (DIY vs. Turnkey Contractor)

National Average
DIY Raw Materials Only
$1,944 – $2,294

Cost of raw lumber, concrete, shingles, wire, or stone without equipment rentals or labor.

Licensed Contractor Turnkey
$4,500 – $6,900

Full installation: permits, site prep, skilled trade labor, equipment, and structural warranty.

Estimated Sweat Equity
~$3,581

Average trade labor savings if executed as a skilled DIY homeowner project.

Verified Trade Contractor NetworkScope Auto-Synced

Compare Up to 3 Free Quotes from Licensed Local Contractors

Skip the heavy equipment rentals, structural liabilities, and municipal permit delays. Connect directly with pre-screened, licensed, and insured trade specialists in National Average.

100% Free Service Zero Obligation Pre-Calculated Project Specs
⚡ Local pros respond in < 2 hours

ACI 302.1R Concrete Volume & Delivered Batching Model

Rendering formula...

Ready-Mix Batching Derivation for 30' × 20' (4" Thick)

  1. Square Footage = 30 ft × 20 ft = 600 sq ft.
  2. Cubic Volume = (600 sq ft × (4 / 12 ft)) / 27 = 7.41 cubic yards.
  3. Applying 8% subgrade tolerance: 7.41 × 1.08 = 8.00 cu yd (rounded to nearest 0.25 yd truck batch).
  4. Order exceeds 4 cu yd minimum: standard full dispatch applies.
Engineering Tip: Verify concrete pumper truck clearance in National Average before pouring if truck cannot back directly to slab edge.

Quick Reference Sizing & Coverage Table

Standard commercial specifications and pre-calculated project benchmarks.

Pre-Calculated
Slab DimensionSquare FootageCubic Yards (4")Cubic Yards (6")Turnkey Contractor Cost
10 × 10 ft100 sq ft1.35 cu yd2.00 cu yd$850 – $1,450
12 × 16 ft192 sq ft2.60 cu yd3.85 cu yd$1,600 – $2,600
20 × 20 ft400 sq ft5.45 cu yd8.00 cu yd$3,200 – $5,400
24 × 24 ft576 sq ft7.80 cu yd11.50 cu yd$4,600 – $7,800
30 × 40 ft1,200 sq ft16.25 cu yd24.00 cu yd$9,600 – $15,800
ACI 302.1R Guide for Concrete Floor and Slab Construction

American Concrete Institute (ACI) 302.1R Specifications

Specifies minimum 4,000 PSI compressive strength mix with 4-inch to 5-inch slump for exterior flatwork and garage floors. Requires vapor retarder (ASTM E1745 Class A) and control joint contraction cuts spaced at a maximum interval of 24 to 30 times slab thickness in inches.

Frequently Asked Questions

How much does a yard of concrete cost delivered in 2026?

The national average cost for ready-mix concrete delivered is $145 to $175 per cubic yard for standard 3,500 to 4,000 PSI mixes. Orders under 4 or 5 cubic yards typically incur a short-load delivery surcharge of $120 to $180.

How much concrete do I need for a 20x20 slab at 4 inches thick?

A 20x20 slab at 4 inches thick contains 400 square feet and requires 4.94 nominal cubic yards. Factoring in an 8% waste and subgrade variance allowance, you should order 5.50 cubic yards of ready-mix concrete.

What is the total turnkey cost per square foot for a poured concrete slab?

Turnkey contractor pricing ranges from $6.50 to $12.50 per square foot including excavation, crushed gravel base, formwork, rebar/mesh reinforcement, concrete pour, and professional broom/trowel finishing.

How thick should a residential concrete driveway or patio be?

Patios and sidewalk walkways should be 4 inches thick. Standard residential vehicle driveways and garage floors should be 4 to 5 inches thick, while heavy RV pads and commercial delivery bays require 6 inches with a #4 rebar grid.

Next Step In Your Project

Related Trade Calculators in this Category

2026 Engine

Garage Door Weight & Opener Horsepower Estimator

Open Calculator
2026 Engine

Garage Door Torsion Spring IPPT & Wind Count Estimator

Open Calculator
2026 Engine

Garage Floor Epoxy Kit, Flake & Topcoat Estimator

Open Calculator
Engineering Specification & Field Manual

Calculation Methodology & Municipal Code Compliance for Concrete Cost Calculator (Delivered Ready-Mix Yards & Turnkey Labor)

Adheres to certified architectural formulas and standard ACI 302.1R Guide for Concrete Floor and Slab Construction commercial trade provisions.

1. Governing Formula & Physical Equations

Accurate material takeoff requires reconciling nominal plan dimensions with real-world physical packaging and volumetric compaction. This engine evaluates Slab Length, Slab Width, Slab Thickness, Subbase Material Prep, Chute / Pour Access against certified engineering multipliers.

\text{Volume (cu yd)} = \frac{\text{Length (ft)} \times \text{Width (ft)} \times (\text{Thickness (in)} / 12)}{27} \times (1 + \text{Waste \%})

Equation Reference: ACI 302.1R Concrete Volume & Delivered Batching Model. Calculated results provide both theoretical net volume and practical jobsite gross totals factoring standard shrinkage and trim cuts.

2. Step-by-Step Field Calculation Protocol

Step 1

Measure Field Dimensions

Measure length, width, depth, or gauge with calibrated trade tools. Confirm grade level and structural subbase.

Step 2

Apply Safety & Scrap Factor

Factor a 5% to 15% allowance depending on job complexity to prevent costly project shutdowns from mid-job shortages.

Step 3

Reconcile Packaging & Labor

Round up to whole commercial packaging units (bags, rolls, panels) and compare raw material cost against regional trade rates.

3. Code Compliance (ACI 302.1R Guide for Concrete Floor and Slab Construction)

Building departments across the United States reference municipal standard codes (including the International Residential Code IRC, National Electrical Code NFPA 70, American Concrete Institute ACI, and ASTM international specs). Designing below these minimum safety thresholds risks structural deflection, inspection failure, and permit revocation.

✓ Verified 2026 Building Code Cycle✓ Regional Frost & Wind Zone Adaptive✓ Dual DIY Material & Turnkey Labor Output

Related Garage, Doors & Concrete Estimators

Complementary trade calculators for synchronized project estimation.

View All Garage, Doors & Concrete Estimators
UL 325 Standard for Door, Drapery, Gate, Louver, and Window Operators2026 Code

Garage Door Weight & Opener Horsepower Estimator

Calculate exact garage door weight based on door dimensions, material, insulation layers, and glass inserts, and select the correct motor horsepower (1/2, 3/4, or 1.25 HP).

DASMA Technical Data Sheet #1022026 Code

Garage Door Torsion Spring IPPT & Wind Count Estimator

Calculate Inch-Pounds Per Turn (IPPT), cable drum radius, spring turns, inside diameter, and wire gauge for residential overhead garage door counterbalances.

ICRI Guideline No. 310.2R / SSPC-SP 13 Surface Preparation2026 Code

Garage Floor Epoxy Kit, Flake & Topcoat Estimator

Calculate 100% solids epoxy base coat gallons, decorative color flakes in pounds, moisture vapor primer, and polyurethane topcoat by car garage bay size.

International Residential Code Section R403.1.32026 Code

Monolithic Slab & Perimeter Footing Concrete Yardage Estimator

Calculate concrete cubic yards for monolithic slab-on-grade foundations, including center slab thickness, thickened perimeter footing trenches, and rebar grid count.